Just How to Remove as well as Replace a Tub.
Just How to Remove as well as Replace a Tub.
Blog Article
Every person seems to have his or her own thinking with regards to How to Install a Bathtub Yourself.
Mounting a bathtub isn't precisely brain surgery, however it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough task. If the old tub is easily accessible, the job can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also position the new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the new one. Make certain you have actually certified on your own for the job as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This write-up will help you set up a new tub in your washroom if you have actually already purchased a new tub as well as do not require to transform the setup of your previous water system pipelines.
Your devices as well as material checklist should comprise the following:
Getting ready for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome as a result of the limited access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water and inspect all joints as well as new pipework for leaks as well as tighten them if essential. Fill the bathtub and also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the tub ought to wait up until the bathtub has been used at least once as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in area between the tap and the sink. Safeguard the faucet in place with the manufacturer provided backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to break a rigid seal, creating the water to permeate the wall in between the bathroom and the tiling, resulting in problems with wetness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to allow for the activity experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our post about How to Install a Bathtub Yourself. Thank you so much for taking a few minutes to read through our article post. Sharing is good. You won't know, you may very well be helping someone out. I enjoy reading our article about How to Install a Bathtub Yourself.
Call Us Now Report this page